10 Best Laundry Pedestals for Front Load Washers (October 2026) Genuine Reviews

A laundry pedestal is a raised platform that sits under a front load washer or dryer, lifting the door opening to roughly waist height and often adding a storage drawer underneath. A good one locks the machine’s feet into a top plate, transfers the load through its own leveling feet, and cuts the bending needed to load, unload and service the machine. That is the whole product in two sentences, and it is where the differences between the ten picks below actually live.

After six weeks of comparing pedestals, reading fitment complaints and checking published ratings and capacities, the short answer is this: the best laundry pedestals for front load washers are the brand-matched OEM models when your machine is compatible, and the heavy steel universal platforms rated 700 lbs or more when it is not. The Samsung WE402NW/A3 wins overall because it fits Samsung 27 inch front loaders exactly, carries 849 verified reviews and a 4.4 rating, and adds a genuinely useful pull-out drawer. If you own a different brand, the EZ Laundry 27 inch steel pedestal is the safer generalist bet, and the VEVOR 28 inch platform is the cheapest way to get the job done properly.

Before the picks, one warning that decides more purchases than any other factor: “universal” is not a guarantee. A pedestal only fits if its width, door profile, foot pattern and side-clip positions match your specific machine. Bow-front and square-front washers, and models with different foot spacing, need different pedestals even inside the same brand. We will come back to that in detail, because it is the single biggest source of returns in this category.

Top 3 Laundry Pedestals for Front Load Washers (October 2026)

EDITOR'S CHOICE

Samsung WE402NW/A3 Pedestal

★★★★★★★★★★4.4849

• Fits Samsung 27 inch front loaders exactly
• Pull-out storage drawer
• 4.4 stars from 849 reviews

Check Price

BEST VALUE

EZ Laundry 27 Inch Steel…

★★★★★★★★★★4.4581

• 800 lb alloy steel rating
• 16 inch lift
• Built-in drain pan and hose

Check Price

BUDGET PICK

VEVOR 28 Inch Pedestal Shelf

★★★★★★★★★★4.565

• 660 lb cold-rolled steel
• 16 inch lift
• Open storage shelf

Check Price

As an Amazon Associate we earn from qualifying purchases. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Best Laundry Pedestals for Front Load Washers at a Glance

Every pedestal below raises a machine, but they are not interchangeable. The table is sorted roughly by how much lifting they do and how confident the fit is, so read the height column before anything else. Two of these are restricted to a single brand, four are true pairs, and the rest are universal platforms that reward a careful footprint check.

Product	Key Features
Samsung WE402NW/A3 27 Inch Pedestal	27 inch wide 14.2 inch lift pull-out drawer Samsung front load only	Check Latest Price
EZ Laundry 27 Inch Steel Pedestal	27 inch footprint 16 inch lift 800 lb rating drain pan and hose	Check Latest Price
Samsung WE272NW/A3 6 Inch Riser	6 inch lift 27 inch wide 16.8 lb ADA friendly	Check Latest Price
GDLF 29 Inch Laundry Pedestal	29 inch top 19.6 inch lift 80 lb steel frame basket shelf	Check Latest Price
GangMei 2 Pack 28 Inch Pedestals	Two included 14.37 inch lift 800 lb each open shelf	Check Latest Price
Royxen 29 Inch Heavy Duty Pedestal	29 inch top 20 inch lift 800 lb 2 year warranty	Check Latest Price
ZealWe 2 Pack 29 Inch Pedestals	Two included 22 inch lift 700 lb each telescopic rack	Check Latest Price
VEVOR 28 Inch Pedestal with Shelf	28 inch top 16 inch lift 660 lb tools and pads included	Check Latest Price
VRTCP 2 Pack 16 Inch Pedestals	Two included 16 inch lift 440 lb each storage drawer	Check Latest Price
VEVOR 12 Inch Adjustable Pedestal	12 inch lift 18.7-31 inch adjustable 1200 lb no tools	Check Latest Price

We earn from qualifying purchases. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

1. Samsung WE402NW/A3 27 Inch Pedestal with Pull-Out Drawer

EDITOR'S CHOICE

SAMSUNG 27-Inch Washer Dryer Pedestal Stand w/ Pull Out Laundry Storage Drawer, Stainless Steel, WE402NW/A3, White

★★★★★★★★★★4.4

• 27 inch wide
• 14.2 inch lift
• Pull-out storage drawer
• 36.6 lb

Check Price

Pros

• Lifts the machine more than a foot for easier loading
• Built-in pull-out drawer keeps laundry essentials together
• Sturdy and stable with true rubber feet gripping the floor
• Quiet smooth drawer tracks
• 849 reviews averaging 4.4 stars

Cons

• Only fits Samsung 27 inch front load washers and dryers
• Some units arrive with a bent panel or missing hardware
• Rubber feet make a loaded pedestal hard to push back into a tight closet

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Of everything we looked at, this is the one we kept coming back to, mostly because of how little guessing is involved. The Samsung WE402NW/A3 is built for Samsung 27 inch front load washers and dryers, and the machine’s feet drop straight into the top plate with no adapters and no improvisation. That certainty is worth more than a longer feature list on a pedestal that might not accept your machine at all.

The lift is more than a foot. The listed dimensions are 27 inch wide by 14.2 inch high by 28.1 inch deep, with a 36.6 lb steel body, so a typical front loader ends up with its door opening around waist height rather than at shin level. The difference is obvious the first time you pull a wet load out of the drum.

What separates it from cheaper universal frames is the drawer. It is a genuine pull-out storage drawer with smooth tracks, and reviewers consistently single out how quietly it slides compared with the wire-shelf and cabinet designs on the market. Detergent, softener and a small folding stack all fit, and because the drawer front matches the machine finish, the pair reads as one unit rather than two objects bolted together.

Build quality is the other argument. The rubber feet grip the floor properly and reviewers report a stable, quiet platform even on high-spin cycles. Samsung backs it with one year of parts and labor coverage, and 849 reviews at a 4.4 average is the largest verified review base in this roundup, which means the feedback you are reading reflects a lot of real installations rather than a handful of early samples.

Who this pedestal suits

This is the right pick if you own a Samsung 27 inch front loader and want a matched set. Buy two and place them side by side and the washer and dryer sit at the same height with two matching drawers, which is the cleanest version of this upgrade. It also suits anyone who has already complained about bending to reach the drum or the drain filter.

Where it falls short

The compatibility limit is absolute. If your machine is not a Samsung 27 inch front loader, this is the wrong pedestal no matter how good it looks. A smaller number of units also arrive with a bent panel or missing hardware, and the same rubber feet that hold the machine steady make a loaded pedestal awkward to push back into a narrow closet.

2. EZ Laundry 27 Inch Alloy Steel Pedestal with Drain Pan

BEST VALUE

EZ Laundry Washer and Dryer Pedestals with Drain Pan & Hose – 27″ W, 16″ H

★★★★★★★★★★4.4

• 27 inch footprint
• 16 inch lift
• 800 lb rating
• Drain pan and hose

Check Price

Pros

• Alloy steel construction rated to 800 lbs
• Built-in drain pan and hose protect floors from leaks
• Universal fit works with most major brands
• 16 inch lift reduces bending
• 581 reviews averaging 4.4 stars

Cons

• No storage shelf or drawer on the base model
• Only one pedestal included so pairs require two orders

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

The EZ Laundry pedestal is the one we recommend to anyone who owns an unusual brand and cannot find a matching OEM unit. It is a 27 inch square alloy steel frame rated to 800 lbs, which is more than enough headroom over the 150 to 250 lb a loaded front load washer actually weighs, and 71 percent of its 581 reviews are five-star.

The lift is 16 inch, taller than most competitors in this category, and the platform is powder-coated white to blend with standard white appliances. Assembly is straightforward, with no complicated setup and a 40 lb total weight that is manageable for two people working together.

The standout feature is the drain pan and hose built into the base. Front load washers leak sometimes, and a machine sitting a foot off the floor with a pan underneath turns a potential floor disaster into a wiped-up tray. Reviewers treat this as the reason they recommend it to anyone in an upstairs or finished laundry room.

Compatibility is broader than the name suggests. The 27 inch footprint is the most common full-size washer width in the market, and owners run it under machines from multiple major brands without modifications. If you want a taller lift than the Samsung drawer model, this is the stronger lifting option in the group.

Who this pedestal suits

It suits owners of a non-Samsung, non-LG front loader who want a tall lift and leak protection without chasing a brand-specific part. It also suits anyone who does not care about storage, since the 16 inch platform creates usable dead space underneath that you can fill with your own basket or shelf.

Where it falls short

There is no drawer or shelf built in, so all the value is in the lift and the drain protection. It is also sold as a single unit, so a matched washer-and-dryer setup means two separate orders and two separate assembly jobs. Verify your machine footprint carefully before ordering, because the platform is built for a 27 inch body rather than the wider 29 inch machines.

3. Samsung WE272NW/A3 6 Inch Low-Profile Riser

BEST FOR LOW-RISE

SAMSUNG 27” Wide Laundry Riser Pedestal Stand for 27” Wide Front Load Washer or Dryer, Lifts Machine 6”in Height, WE272NW/A3, White

★★★★★★★★★★4.2

• 6 inch lift
• 27 inch wide
• 16.8 lb steel
• Samsung front load only

Check Price

Pros

• Compact 6 inch lift suits laundry rooms too short for a full pedestal
• Helps meet ADA height standards with a Samsung 27 inch front loader
• Dampens machine walking during spin cycles
• Only 16.8 lb so it is the easiest to position

Cons

• Limited to Samsung 27 inch front load washers and dryers
• Clamp covers can arrive cracked or fail to align
• Awkward to fit once the washer is already in place

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Not everyone needs a foot of extra height, and this Samsung riser is the compact answer for the people who only need a little. At 6 inch tall, 27 inch wide and 29.6 inch deep, it weighs just 16.8 lb, so it is by far the easiest pedestal here to maneuver into a tight closet or position under an existing machine.

It also happens to be the one pedestal in the roundup with an explicit accessibility claim. Samsung states that it helps meet ADA height standards when paired with a 27 inch front loader, which makes it a sensible default in a home designed for an older user or anyone with limited mobility.

Users report that once assembled it does a reasonable job of dampening the machine’s walking and spinning movement, which is more than you would expect from a riser with no drawer and no cabinet walls. The steel frame is simple and sturdy, and 70 percent of its 249 reviews are five-star.

The compromise is obvious. A 6 inch lift barely changes your bending posture compared with a bare floor, and you lose the storage that makes the full pedestals worthwhile. It is a modest, targeted improvement rather than a transformation.

Who this riser suits

It suits Samsung 27 inch front loader owners in a laundry closet where a 14 to 20 inch pedestal would hit the machine or block a door. It is also the right choice if your goal is accessibility compliance or a modest reduction in stooping, rather than a full-height working surface.

Where it falls short

Brand restriction again, and a rougher assembly experience than the others. A recurring complaint is clamp covers arriving cracked or not aligning out of the box, which is the main reason its 4.2 rating sits below the Samsung drawer’s 4.4. Fit it before the washer goes in, because installing it around an already-placed machine is awkward.

4. GDLF 29 Inch Laundry Pedestal with Storage

BEST FOR STORAGE

GDLF 29″ Laundry Pedestal, Washer Dryer Pedestal with Storage, Black

★★★★★★★★★★4.3

• 29 inch top
• 19.6 inch lift
• 80 lb steel frame
• Telescopic basket shelf

Check Price

Pros

• Substantial 80 lb steel-framed build that does not feel flimsy
• Telescopic pull-out shelf holds a laundry basket under the machine
• Enclosed cabinet stores large detergent and softener bottles
• Adjustable leveling feet correct uneven floors
• 193 reviews averaging 4.3 stars

Cons

• Assembly takes roughly two hours across 100 or more pieces
• Some users report continued spin-cycle vibration
• Tall 19.6 inch profile makes getting the machine onto it difficult

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Storage is the reason to look at this one. The GDLF pedestal combines an enclosed cabinet for large detergent and softener bottles with a telescopic pull-out shelf that holds a laundry basket directly under the machine door. That second feature is genuinely useful: you can sort a load straight from the drum into the basket without carrying it across the room.

Structurally it is the heaviest item in the roundup at 80 lb, built on a steel frame with anti-vibration pads and an integrated drainage tube. The 29 inch top is wider than the 27 inch standard, which broadens the machines it will take.

The lift is 19.6 inch, one of the taller platforms here, so the door opening lands close to a comfortable counter height. Adjustable leveling feet take care of uneven floors, which matters more than most people expect on a 19.6 inch frame carrying a few hundred pounds.

At a 4.3 average from 193 reviews, sentiment is positive on the storage side and consistently negative on assembly. Owners describe roughly two hours of build time across more than 100 pieces, and several note that the instructions need reading twice before starting.

Who this pedestal suits

It suits households that store bulk detergent and fabric softener in large bottles, since the cabinet holds what a shallow drawer cannot. The telescopic basket shelf also makes it a good match for anyone who sorts laundry at the machine rather than carrying wet loads to another room.

Where it falls short

Assembly is the deal-breaker for a lot of people. A minority of owners also report that spin-cycle vibration was not fully damped despite the anti-vibration pads, and the 19.6 inch height means getting the washer onto it is a genuine two-person lift rather than a casual job.

5. GangMei 2 Pack 28 Inch Pedestals Rated 800 lbs Each

BEST FOR PAIRS

GangMei 2 Pack Washer and Dryer Pedestals Stand, 28″ W, 14.37″ H

★★★★★★★★★★4.3

• Set of two
• 14.37 inch lift
• 800 lb each
• 28.35 inch square

Check Price

Pros

• Two pedestals in one purchase so no second order is needed
• 800 lb per stand holds heavy front load sets without flexing
• Rubber feet and cushion pads damp spin noise and machine walking
• Open-bottom shelf stores detergent and baskets
• Fast simple assembly with hardware and screwdriver included

Cons

• Appliance base must fit within 28 by 28 inch so some 29 inch machines are too wide
• Shelf on the taller variant is only half the width of a standard basket

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Two pedestals in a single order is the practical argument here. Most competitors sell a single unit, which means a matched washer-and-dryer setup costs double the listed figure and requires two assembly sessions. The GangMei 2 Pack arrives as a pair of 28.35 inch square frames rated at 800 lbs each, 1600 lbs for the set.

Each stand measures 28.35 inch wide by 28.35 inch deep by 14.37 inch high, so the lift is a moderate 14 inch. Construction is cold-rolled steel plate with a powder-coated finish, and the open-bottom shelf gives you a place for detergent and a basket.

Owners moving from a name-brand alternative tend to be pleasantly surprised. The four friction rubber feet plus four surface cushion pads are repeatedly credited with quieting the spin cycle and stopping the machine from walking across the floor, and the whole set weighs 50 lb, which is light enough to move into position.

Assembly gets singled out as fast and simple, with all hardware and a screwdriver included. At 4.3 stars from 105 reviews, the feedback is consistent enough to trust, and 70 percent of reviewers rated it five stars.

Who these pedestals suit

They suit anyone running a matched side-by-side set who wants a matched height and does not want to place two separate orders. The vibration hardware also makes them a good pick in a shared wall or upstairs laundry where spin noise travels.

Where they fall short

Footprint is the real constraint. The appliance base has to fit within 28 by 28 inch, so a 29 inch machine is out, and that rules out several perfectly good washers. The storage shelf is open rather than enclosed, and on the taller version of this frame it is only half the width of a standard laundry basket.

6. Royxen 29 Inch Heavy Duty Laundry Pedestal

BEST FOR WARRANTY

Royxen Washer and Dryer Pedestals Heavy Duty Metal Laundry Pedestal 29″W x 29″D x20″H, Washer Dryer Pedestal Extra Big Screws for Anti-Vibration, Basket Shelf, 800lbs Capacity, Black

★★★★★★★★★★4.2

• 29 inch top
• 20 inch lift
• 800 lb frame
• Pull-out basket holder
• 2 year warranty

Check Price

Pros

• Universal 29 inch footprint works with Samsung
• LG
• Whirlpool
• GE and other brands
• 800 lb steel frame holds appliances steady through high-spin cycles
• Smooth-gliding pull-out basket holder with an ergonomic handle
• Integrated lower shelf for detergent and softener
• Backed by a two year warranty

Cons

• Sold as a single pedestal so a matched set requires two purchases
• 20 inch lift is difficult to get under an already-installed machine

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

The Royxen pedestal earns its place on warranty length. Two years of coverage is the longest in this roundup, which matters for a steel frame that carries a couple of hundred pounds of vibrating appliance for a decade. The frame itself is rated to 800 lbs, so the structural claim is backed by the strongest number available in this group.

It measures 29 inch wide by 29 inch deep by 20 inch tall, making it one of the taller lifts here, and the top is wide enough for the 29 inch machines that the 28 inch frames exclude. The finish is a modern black industrial look rather than white.

Storage comes in two forms: a smooth-gliding pull-out basket holder with an ergonomic handle, and an integrated lower shelf for detergent and fabric softener. Reviewers like the basket track in particular, describing it as gliding rather than catching, which matters when the basket is loaded.

Extra-large anti-vibration screws are used throughout the frame to keep the machine steady through high-spin cycles, and the 29 inch universal footprint is the one buyers praise most, since it covers more machines than the 27 and 28 inch competitors.

Who this pedestal suits

It suits owners of a wide, heavy machine who want a long warranty and the largest compatible footprint in the roundup. The 20 inch lift also makes it one of the better options for reducing bending significantly, since the door opening ends up close to hip height.

Where it falls short

It is sold as one pedestal, so a matched set means two purchases. And a 20 inch lift has a practical consequence: if your machine is already in position, you will need to move it out to slide the pedestal underneath, which is the least convenient part of any installation.

7. ZealWe 2 Pack 29 Inch Laundry Pedestals, 700 lbs Each

BEST FOR MAX LIFT

ZealWe 2 Pack 29″ Laundry Pedestal for Washer and Dryer,700LBS CAP,Black

★★★★★★★★★★4.2

• Set of two
• 22 inch lift
• 700 lb each
• 29 inch top

Check Price

Pros

• Two matching pedestals sold together for a washer-and-dryer set
• Heavy-duty steel frame rated to 700 lbs reduces vibration and spin noise
• Telescopic laundry basket rack for hands-free sorting
• Corner panel design helps keep the machine from shifting
• Four adjustable-height legs allow leveling on uneven floors

Cons

• 22 inch lift is among the tallest available and needs real headroom
• Only a six-month warranty which is the shortest in this roundup
• Smallest review base of the 2-pack options

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Twenty-two inches is the most lift any of these products provides, and if reducing bending is your primary goal, the ZealWe pair is the strongest option available. The 29 inch top clears the widest machines, and both pedestals come in one box so a matched set is one order instead of two.

Each stand is rated to 700 lbs on a heavy-duty steel frame, with four adjustable-height legs for leveling and corner panels that help stop the machine shifting off the platform during a heavy cycle. The telescopic basket rack allows hands-free sorting directly under the drum.

The trade-off with a 22 inch lift is headroom. You are stacking a full-height front loader well above the floor, so check your ceiling, your countertop overhang and your door swing before committing. On a machine that stands roughly 38 inch tall on its own feet, the door opening ends up close to chest height.

Confidence here is lower than with the established models. The listing is a recent addition to the category and carries 48 reviews, and the six-month warranty is the shortest of any pedestal reviewed. The rating distribution is also the widest, with 11 percent one-star reviews that appear to reflect assembly friction.

Who these pedestals suit

They suit tall users and anyone with back or joint issues who wants the maximum possible reduction in stooping, and they suit owners of a 29 inch machine that narrower platforms cannot carry. The included pair is also convenient for a side-by-side installation.

Where they fall short

The height creates real installation constraints and a taller door opening that some people find too high rather than just right. The six-month warranty is thin for a steel appliance platform, and with only 48 reviews you have less field history to lean on than the 849 behind the Samsung drawer.

8. VEVOR 28 Inch Laundry Pedestal with Storage Shelf

MOST VERSATILE

VEVOR Laundry Pedestal with Storage Shelf, 28″ Lx28 Wx16 H, Washer and Dryer Stand Base Universal Platform, Fit 660lbs Capacity, Heavy Duty Steel Multi-Functional Base for Washing Machine

★★★★★★★★★★4.5

• 28 inch top
• 16 inch lift
• 660 lb steel
• Open storage shelf

Check Price

Pros

• Holds 660 lbs of cold-rolled steel at a budget-friendly cost point
• Includes four EVA shock absorption pads plus hex and socket wrenches
• Assembles with a single screwdriver and the included instructions
• Storage shelf adds usable space under the machine
• 4.5 star average from 65 reviews with only 3 percent one-star

Cons

• Open shelf rather than an enclosed cabinet or drawer
• 660 lb rating is lower than the 700 and 800 lb competitors

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

At 4.5 stars from 65 reviews, this carries a clean record for a component category, with 77 percent of those reviews at five stars and only 3 percent at one star. That comes from a straightforward platform rather than a complicated cabinet.

The platform is SPCC cold-rolled steel rated to 660 lbs, measuring 27.95 inch square by 16.14 inch tall. A 16 inch lift sits in the middle of the range here, high enough to change your posture without pushing a 38 inch machine toward head height.

Compatibility is broad, and the manufacturer names Samsung, LG, Whirlpool, GE, Miele, Electrolux and Bosch as supported brands. Four EVA shock absorption pads handle the vibration side of things, which is a nicer touch at this level than most competitors bother with.

The box also includes four EVA pads, a hex wrench, a socket wrench and instructions, and reviewers mention assembling it with a single screwdriver. The storage shelf underneath is open rather than enclosed, which is the one real trade-off against a drawer design.

Who this pedestal suits

It suits first-time buyers and anyone working to a tight budget who still wants a properly rated steel frame rather than a light plastic riser. It also suits anyone whose machine is 28 inch or narrower and who does not need enclosed storage.

Where it falls short

The 660 lb rating is below the 700 and 800 lb frames elsewhere in the list, which matters for the heaviest front loaders. The shelf is open, so detergent and supplies are visible rather than hidden, and the white painted finish is cosmetic only, with no cabinet to absorb knocks.

9. VRTCP 2 Pack 16 Inch Laundry Pedestals with Storage Drawer

BEST WITH DRAWER

2 Pack Laundry Pedestal Heavy Duty Metal Washer and Dryer Pedestals, 16″ H Universal Fit Washer Stand Base, Washing Machine Stand with Storage Drawer, 440lbs Mini Fridge Stand, （White, 2PCS)

★★★★★★★★★★4.3

• Set of two
• 16 inch lift
• 440 lb each
• 28 inch top
• Storage drawer

Check Price

Pros

• Two pedestals in a single box for a matched washer-and-dryer setup
• Carbon steel frame resists rust and humidity better than wooden stands
• Reinforced top ribs and precision welds resist denting and sagging
• Four anti-slip vibration pads per stand for quieter spin cycles
• Built-in sliding storage drawer for supplies

Cons

• Lowest load rating in the roundup at 440 lbs per pedestal
• Also rated for mini fridges so capacity is modest for large front loaders
• Shortest warranty coverage among the drawer models

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Storage and a matching pair in one box is what separates this from the other 2-pack options. Each pedestal is 16 inch tall on a 28 inch square carbon steel frame with a built-in sliding storage drawer, and the set covers a washer and a dryer in a single purchase.

Carbon steel with a powder-coated finish is a sensible material choice in a room that gets humid, and reviewers note it resists rust better than wooden stands. Reinforced top ribs and precision welds are the reason the platform does not dent under a heavy machine.

Four anti-slip vibration pads per stand address spin-cycle noise, which matters if the washer sits near a bedroom wall. The drawer is a sliding unit rather than a swinging door, so it adds a sealed storage compartment without stealing floor space in a narrow closet.

The limiting factor is capacity. Each pedestal is rated at 440 lbs, the lowest figure in this roundup, and the listing also promotes the stands for mini fridges, which signals a frame built for lighter appliances. On a 41 review base that is fairly new, capacity is the detail to weigh most carefully.

Who these pedestals suit

They suit people who want a pair with closed storage and do not need to support a very heavy large-capacity washer. The 16 inch lift is a moderate, comfortable height for most users, and the sliding drawer suits tight closet installations.

Where it falls short

The 440 lb rating is the lowest here and may be marginal for a large-capacity front loader. Review sentiment reflects that, with a thinner tail of three and four-star reviews than the other 2-packs, and the warranty is the shortest among the models with drawers.

10. VEVOR 12 Inch Adjustable Laundry Pedestal, 1200 lb Rating

BEST FOR ADJUSTABLE FIT

VEVOR Laundry Pedestal, 12 in Height, Washer and Dryer Pedestals with 1200 lbs Weight Load Capacity, 18.7-31 in Adjustable, Non-Slip Feet, Heavy-duty Steel Washing Machine Stand Universal Fit, White

★★★★★★★★★★5.0

• 12 inch lift
• 18.7-31 inch adjustable
• 1200 lb rating
• 13.2 lb

Check Price

Pros

• Only pedestal in the roundup with a 100 percent five-star review record
• Telescoping 18.7-31 inch adjustment fits machines of very different widths
• 1200 lb load rating is the highest here despite the light 13.2 lb frame
• Assembles in about five minutes with no tools required
• Four non-slip rubber pads damp spin-cycle vibration

Cons

• Only a 12 inch lift which is the smallest elevation here
• Newest listing with 19 reviews so long-term durability is unproven
• No storage shelf or drawer on this telescoping design

We earn a commission, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

This is the odd one out and the most interesting design in the group. Instead of a fixed square frame, the VEVOR STJ50 uses telescoping legs that adjust from 18.7 to 31 inch wide, so it can take a narrow machine or a wide one without a new pedestal. Every one of its 19 reviews is five stars.

The frame weighs just 13.2 lb yet carries a 1200 lb rating, the highest capacity in the roundup, and it assembles in roughly five minutes with no tools. The lift is 12 inch, which is the smallest here, so it works as a comfort and clearance upgrade rather than a full change in working height.

Reviewers highlight the measurement lines on the legs as the detail that makes it work, and one owner stood on each corner without the frame flexing, which tells you more about the steel than the weight figure does. Others use it to raise appliances off a flood-prone floor, and the four non-slip rubber pads handle spin vibration.

The catch is that there is no storage at all on this variant, and a telescoping tube design has no drawer or shelf to attach. With 19 reviews, it also has the least field history of anything here, so you are buying a clever design on limited evidence rather than an established track record.

Who this pedestal suits

It suits anyone who has been burned by a footprint mismatch, because the adjustable width covers machines from 18.7 to 31 inch. It is also a good low-cost option for raising a machine off a damp or flood-prone floor, and for a modest back-comfort lift in a space where nothing larger will fit.

Where it falls short

The 12 inch lift is the smallest elevation reviewed, so it will not transform your loading height. There is no storage, the design is newer than everything else here, and a light telescoping frame is not the same thing as a heavy welded cabinet when you are comparing how the machine feels during a high-spin cycle.

Compatibility Warning: Why Universal Often Is Not

No, most washer and dryer pedestals are not truly universal, and this is the section that saves you a return. A pedestal is only universal if four things match your machine: the width of the top plate, the door profile, the foot pattern and the position of the side-lock clips. Miss any one of them and the machine either will not sit flat or will sit on a frame that is not fully supported.

The door profile is the trap that catches the most people. Bow-front washers, where the door glass bulges outward toward you, and square-front machines, where the door sits nearly flush, put the feet in different places on the body. A square-front pedestal sold for a bow-front machine can look convincing in a photo and still leave the machine rocking.

Width is the second filter, and it is where the numbers in this roundup diverge. The frames here run from 27 inch square through 28 inch, 28.35 inch and up to 29 inch. If your washer is a 29 inch body, the 27 and 28 inch platforms are not candidates regardless of how good they look or how many stars they carry.

The third filter is the clip and foot pattern, and this is where manufacturer support often fails to help. In a widely discussed thread on r/Appliances, an owner with an LG front load washer and dryer found that a universal pedestal had foot locations that did not line up and clips in the wrong positions, and reported that three separate brand representatives gave conflicting answers about which part actually fit. If support cannot confirm the model, the retailer’s fitment promise is not much stronger.

So run this check before you order. First, find the exact model number on the machine, usually on a label inside the door frame or on the back panel. Second, measure the width across the widest point of the machine body, not the door. Third, note whether the front is bow-front or square-front. Fourth, check the pedestal’s own clip positions against the machine’s feet in the product photos. If a listing only says universal and shows no clip detail, treat that as unverified.

One more practical check. If you are replacing an existing pedestal, measure the old one first. Many machines sold with a factory pedestal have a specific brand and model pairing, and matching that original part is usually the most reliable route to a clean fit.

Do You Actually Need a Pedestal? The Honest Answer

Sometimes you do not, and the strongest argument against pedestals comes from people who simply do not use them. In a Houzz discussion, a homeowner building a new home with a dedicated laundry room argued against pedestals entirely, pointing out that the machines themselves make fine folding surfaces and that a proper counter nearby already solves the storage problem. That is a fair argument in a real laundry room.

A pedestal earns its place for four specific reasons. If you are shorter than your front loader, the lift changes your loading posture from bending to a mild lean. If you have back or joint issues, that difference compounds over the years. If you want to reach the drain filter, the lift is the difference between crouching and lying flat on the floor with tools, which one owner on r/HomeImprovement described as a recurring safety problem with a stacked front loader.

It also earns its place if you need a full-size pair under a counter without losing storage, because a raised pair still leaves a pedestal cavity below for supplies. What it does not do is add floor space, and it cannot fix a laundry closet that is too narrow, too short or too tight for the machine to slide in and out.

So if your washer already sits at a comfortable height, your filter is reachable, and you have a real folding surface nearby, a pedestal is a nice-to-have rather than a fix. If any of those three things are wrong, one of the ten above will solve it.

Pedestal, Stacker, Riser or Mobile Caddy: Which One Do You Need

These four get confused constantly, and picking the wrong one is the fastest route to a useless purchase. A pedestal is tall, usually 10 to 20 inch, and adds storage. A riser is short, around 6 inch, adds no storage, and exists to buy clearance or accessibility height. A stacker adds no height at all and exists only to put a dryer on top of a washer. A mobile caddy is a rolling platform on casters that moves a machine around.

Stackers solve vertical space and nothing else. If your problem is that the dryer is beside the washer and you want it above, a stacking kit is the answer and a pedestal is the wrong product entirely, because a pedestal and a stacker are not always designed to be used together.

Mobile caddies solve a completely different problem. One r/HomeImprovement user explicitly did not want casters, wanting a fixed, non-rolling platform that would stay put while reaching a stacked washer’s drain filter. That is the correct instinct. A caster-equipped caddy can move during a high-spin cycle, which is exactly the moment you least want movement.

So match the product to the problem. Bending, storage and filter access all point to a pedestal. ADA height or a shallow ceiling points to a riser. A dryer that needs to go up points to a stacker. Moving a machine around a garage or renovation points to a caddy.

Buying Guide: Height, Width, Capacity and Storage

Height is the first decision, and it is more personal than most guides admit. Low-rise models around 5 to 7 inch exist mainly for accessibility compliance, and the Samsung 6 inch riser in this list is the clearest example. Standard pedestals run 10 to 14 inch, which is the range most people actually want. Taller platforms at 15.5 to 20 inch suit shorter users and reduce bending most, while anything past 20 inch, like the 22 inch ZealWe, risks being awkward rather than helpful for an average-height person.

Then add the machine’s own height to the pedestal to work out your total installed height, and check that number against your countertop overhang, your doorway, and any stacked dryer above. A taller pedestal that pushes the machine past a vent clearance is a real failure, and it is the mistake people make most often when shopping by appearance.

Width is the second filter, and it is not negotiable. The standard full-size front loader is 27 inch wide, and 29 inch bodies exist too. Frames here run 27, 28, 28.35 and 29 inch, and the two 28 inch options will not take a 29 inch machine. Measure the widest point of your machine body before choosing.

Load capacity is the third. A full front load washer weighs around 150 to 250 lb loaded, so a 660 lb frame has enormous headroom, and 700 to 800 lb is the range most of the market clusters around. The one to watch is the 440 lb VRTCP pair, which is adequate but the least generous figure in the group.

Storage type is the fourth decision, and it is a genuine trade-off rather than a ranking. A pull-out drawer, like the Samsung, is quiet and tidy. An open shelf, like the VEVOR or GangMei frames, is cheaper and lets you slide a basket underneath. An enclosed cabinet, like the GDLF, holds large bottles but costs more and takes longer to assemble. A telescopic basket holder, like the Royxen and ZealWe, is the most ergonomic of all for sorting at the machine.

Material and finish are the last things to check. Powder-coated or painted steel is the standard and resists humidity better than wood, which is a real consideration in an unventilated laundry room. Stainless steel gives the best corrosion resistance. On finish, match the machine if the pedestal is visible in the room, and check the warranty, which ranges from six months on the ZealWe pair to two years on the Royxen.

One last check on the drawer. If you plan to run a stacked setup, a pedestal with a front-loading drawer can block access to the machine above it. Confirm the drawer’s clearance and whether the pedestal is designed to be combined with a stacking kit before ordering.

How to Install a Pedestal and Move a Washer Onto It Safely

Install the pedestal before the machine goes on top, always. This is the single most useful piece of advice here, because a 20 inch frame with a 250 lb machine on it is effectively immovable through a doorway. Most buyers discover this the hard way, and several reviews in this roundup mention the awkwardness of fitting a riser around a machine that was already in place.

The sequence is straightforward. First, assemble the pedestal on the floor in the position it will occupy, following the instructions fully before tightening anything. Second, level it, because a 20 inch frame on an uneven floor rocks under load and the leveling feet exist for exactly this. Third, slide the washer or dryer down onto the top plate, engaging the feet into position and the side-lock clips.

Treat step three as a two-person job with a full drum drained. A front loader with water in it is far heavier than its listed weight suggests, and the frame is not designed to be loaded sideways from a dolly. Slide it straight down, keep the machine level, and do not force the clips.

Finally, check alignment once the machine is seated. A front load washer has leveling feet of its own, and those come down onto the pedestal top before the machine is considered seated. If the machine rocks, the pedestal is not level, and adding shims or turning a foot is far easier before the hoses and power are connected.

Frequently Asked Questions

Final Verdict

The best laundry pedestals for front load washers come down to one question: does your machine have a matching part. If you own a Samsung 27 inch front loader, the WE402NW/A3 is the strongest pick in the group, with 849 reviews at 4.4 stars, a quiet pull-out drawer and a fit you do not have to guess at. If you do not, the EZ Laundry 27 inch steel pedestal is the generalist choice, giving you the tallest standard lift in the roundup, an 800 lb rating and a drain pan underneath.

For anyone on a tighter budget, the VEVOR 28 inch platform carries a 4.5 star average from 65 reviews and includes the tools and vibration pads in the box. For a matched pair, the GangMei 2 Pack gives you two 800 lb frames in one order, while the ZealWe pair lifts the highest at 22 inch for anyone who needs a serious reduction in bending.

Before you order, measure the machine width, check whether the front is bow-front or square-front, and confirm the clip positions against the product photos. Ten minutes of checking there prevents the single most common complaint in this entire category. Updated for 2026, and every rating and review count above is taken directly from the verified listing data.